Countersunk Magnet Manufacturer & Supplier

 

Our countersunk neodymium magnets feature precision-machined conical mounting holes for secure screw installation and a low-profile fit in industrial equipment, fixtures, furniture, display systems, and magnetic assemblies. As a countersunk magnet manufacturer and supplier, Xiamen Zhaobao Magnet Co., Ltd. offers customized magnet dimensions, magnetic grades, countersink hole sizes, holding force, magnetization direction, and protective coatings to meet specific application requirements.

 
 
Specifications & Material Options

 

Material Grade

Residual Flux (Br, kGs)

Intrinsic Coercivity (Hcj, kOe)

Max. Operating Temperature (°C)

Standard Screw Compatibility

N35–N52

11.7–14.8

≥ 12

80

M3, M4, M5, M6 (DIN 965 / ISO 7046)

N35M–N50M

11.7–14.5

≥ 14

100

M3–M8, #4–#10 UNC

N35H–N48H

11.7–14.2

≥ 17

120

M4, M5, M6 heavy-duty fasteners

N35SH–N45SH

11.7–13.8

≥ 20

150

High-vibration automotive and motor brackets

Sm2Co17 (SmCo)

10.2–11.2

≥ 20

300

M3–M6 high-temperature industrial fixtures

 

Protective Surface Coatings

Surface Coating

Coating Thickness

Corrosion Protection / Performance

Typical Application

Triple-Layer Ni-Cu-Ni (Nickel-Copper-Nickel)

12–20 μm

Standard electroplated protection; salt-spray tested to ASTM B117 for 24–48 hours

General-purpose indoor applications

Black Epoxy Coating

15–30 μm

Enhanced corrosion resistance; salt-spray tested to ASTM B117 for over 96 hours

Humid and outdoor environments

Chemical Passivation / Zinc (Zn)

8–12 μm

Thin protective layer for cost-sensitive applications

Interior hardware and general-purpose fixtures

 

Customization & OEM Services

Bore Geometry & Chamfer Angles

Standard 90 deg countersink angle aligned to ISO/DIN flat-head screw head profiles. Custom 82 deg countersink angles available for US imperial fasteners (#4, #6, #8, #10 flat head).

Polarity Matching (Matched Pairs)

Supplied in matched pairs (50% North-faced countersink, 50% South-faced countersink) packed in separated color-coded trays to streamline manual or automated door-latch assembly.

Dimensional Tolerances

Ground to +/- 0.05 mm on outer diameter/length and +/- 0.05 mm on bore center-line concentricity.

Torque-Relief Engineering

Optimized bore wall thickness ratios to withstand recommended tightening torques (up to 2.5 N*m for M4 screws) without structural cracking.

 

 

Quality Control & Compliance

Automated Optical Sorting: 100% vision sensor screening for micro-cracks, edge chipping around the countersink rim, and dimensional deviations.

 

Polarity Verification: Automatic hall sensor check on 100% of production items to eliminate pole polarity mixing prior to packaging.

 

Pull Force Testing: Vertical breakaway force validation using calibrated load cell test stands against 10 mm polished structural steel plates (St37).

 

Coating Thickness Verification: X-ray fluorescence (XRF) spectrometry measuring plating thickness across flat surfaces and inside the inner countersink bevel.

Countersunk Rare Earth Magnets
Packaging & Bulk Supply
 

Anti-Crushing Tray Packing

Custom vacuum-formed plastic trays with individual cutouts holding each magnet separated, protecting countersunk edges from impact.

Magnetic Shielding for Air Freight

Master cartons lined with 1 mm sheet iron to restrict stray magnetic fields below 0.00525 gauss at 15 feet, fulfilling IATA Dangerous Goods Regulations (PI 953).

Moisture Barrier

Sealed polyethylene bags containing desiccant packs to prevent moisture ingress during long-haul ocean shipping.

Kitting & Private Label

Customized inner box labeling with barcode data, screw pairing kits, and custom part numbers for OEM distributors.

 

Certifications
productcate-1-1
productcate-1-1
productcate-1-1
productcate-1-1

 

 

FAQ

 

 

Q: How do I choose between North-facing and South-facing countersunk magnets?

A: If mounting a magnet directly onto a ferrous steel surface, pole facing does not affect pull force. When mounting two countersunk magnets to attract face-to-face (such as a door latch), you must specify one magnet with the North pole on the countersunk side and the second with the South pole on the countersunk side.

Q: What prevents countersunk magnets from cracking when tightening the screw?

A: Neodymium is a brittle ceramic-like material. Cracking occurs if the screw head applies uneven localized compression or over-torqueing. We design sufficient wall thickness around the bore, recommend non-countersunk flat washers under excessive torque, and provide target torque limit specs (e.g., maximum 1.2 N*m for M3 screws).

Q: Are these countersunk magnets supplied with standard matching screws?

A: Magnets are typically supplied without screws to allow customers to choose fastener material (e.g., 304 stainless steel vs. zinc-plated steel). However, custom hardware kitting with pre-selected ISO/DIN flat-head screws can be integrated into bulk packaging upon request.

Q: Why does a pot-type countersunk magnet provide higher pull force than a plain disc magnet?

A: Pot magnets enclose the rare-earth core inside a steel cup. The steel casing redirects the magnetic flux from the non-working back face directly to the front contact perimeter, amplifying holding force while protecting the brittle magnet edge from side impacts.

Q: What is the standard manufacturing lead time for custom countersunk sizes?

A: Tooling modification and prototype sampling take 10 to 14 days. Mass production batches ranging from 5,000 to 100,000 pieces require 20 to 30 days including sintering, machining, plating, testing, and magnetic shielding packaging.

Q: Do non-magnetic stainless steel screws affect the performance of countersunk magnets?

A: Using 304 or 316 non-magnetic stainless steel screws prevents flux distortion through the screw head and ensures maximum surface flux concentration on the targeted holding substrate.

 

Request a Quote

 

 

To receive a detailed commercial and technical proposal, submit your inquiry with the following details:
1. Magnet geometry (Disc, Block, or Pot) and key dimensions (Outer Diameter / Dimensions, Height, Screw Size/Inner Bore diameter).
2. Required magnetic grade (e.g., N35, N42, N35SH) or required operating temperature.
3. Polarity requirement (North on countersink face, South on countersink face, or Matched Pairs).
4. Coating type and estimated annual order quantity.

The supplied contact details list zb16@magnets-world.com and a response target of 12 working hours, with standard samples in 3–5 business days and custom-logo prototypes in 7–10 days. Confirm these commercial details, sample availability, and the actual manufacturing location before publication.

As one of the leading countersunk magnet manufacturers and suppliers in China, we have world-leading production equipment and strong manufacturing capabilities. Please rest assured to wholesale high quality countersunk magnet at competitive price from our factory. Customized orders are welcome.